Booking

Are you searching for help about Tools You Need to Install a New Bathtub ?

Installing a bathtub isn't exactly brain surgery, however it does require solid plumbing, carpentry, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably tough job. If the old tub is conveniently obtainable, the job can relocate rapidly; if you need to open a wall to eliminate the old bathtub and place the new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will require an assistant to leave the old bathtub and also embeded in the brand-new one. Ensure you have qualified on your own for the job as well as are comfortable attempting it. As opposed to employing a contractor to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This write-up will certainly assist you mount a new bath tub in your washroom if you have already bought a new bathtub and also don't require to alter the arrangement of your previous water supply pipes.
Your tools and also material list need to make up the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the restricted access that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end provides a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making certain that the washers remain in location in between the tap as well as the sink. Safeguard the faucet in position with the maker offered backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal faucet ports. The previous type needs to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

Installing the Bath tub

Using both wooden boards under its feet, put the bathtub in the required placement. The wooden boards are useful in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the tub until the level reviews level.
To mount taps, fit the bottom of the furthest adaptable tap adapter to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water as well as check all joints as well as brand-new pipework for leaks as well as tighten them if required. Load the bath tub and additionally check the overflow electrical outlet and also the normal electrical outlet for leaks.
Finally, repair the bath paneling as explained in the supplier's user's manual. Tiling as well as sealing around the bathtub ought to wait until the bath tub has actually been used a minimum of once as this will resolve it into its last setting.

Planning for the Installation

First of all, the sustaining framework provided with the bathroom needs to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets system to avoid pressure on the tub.
Fit the flexible faucet connectors to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently be ready to be suited its last setting.

Tiling Around the Bath tub

In the area where the bath fulfills the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to crack a stiff seal, creating the water to permeate the wall in between the bath as well as the tiling, causing problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealer can break rather early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly available on the market. It is recommended to fit the ceramic tiles making use of waterproof or water-proof adhesive and grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We had been brought to that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a friend on our other web blog. You should set aside a second to distribute this blog posting if you enjoyed it. I am grateful for your time. Kindly check our site back soon.

Immediate support available.